维修机械手：STAR星达、哈镆、劲力、精锐、天行、赛尔、实达昆、富井以及各种国产机械手。

The mold does not

1) Is the vertical cylinder descending?

1) Press the Up key to raise the vertical

      close

2) Does the productconfirmation

    cylinder

  limit switch come on after the

2) Adjust the limit switch and check the wiring

 模具不关闭

    product is chunked automatically?

3) Check the ON conditions and the interlock

　

3) Is the mold close safety signal

4) Check the ON conditions to see if they are

　

   comes on?

    correct.

　

4) Is the cycle start display ON?

　

　

　

1)  使用操作面板的上来上升机械手

　

1) 机械手是否竖直下降

2) 检查限位开关及相关连线

　

2) 产品被夹住后产品确认限位开关是否

3) 检查ON的条件和互锁

　

   自动转ON

4) 检查ON的条件是否满足

　

3) 模具关闭安全信号是否转ON?

　

　

4) 周期开始的显示是否为ON?

　

The Mold does not

1) Is the vertical cylinder descending?

1) Press the Up key to raise the vertical cylinder

open

2) Is the mold open safety signal

2) Check the On conditions and the interlock

模具不开

   comes on?

　

　

　

1) 使用操作面板的上来上升机械手

　

1) 机械手是否竖直下降?

2) 检查ON的条件是否满足

　

2) 模具关闭安全信号是否转ON?

　

No descent movement

1) Is the mold open conplete (MO)

1) Adjust the limit switch on the molding

无下降动作

   signal comes on?(extracting-side)

    machine and check the wiring of the

　

2) Are the swing action-end and swing

    control box.

　

   return-end limit switches(on the

2) Adjust the limit switch on the molding machine 

　

   extracting and release side) function

    and check the wiring.

　

   correctly?

3) Loosen gradually until descent movement starts.

　

3) Is the desent speed control valve shut

4) Replace bad valve.

　

   too tightly?

5) See the section"Manual Operations"  and

　

4) Is the solenoid valve bad?

   "Automatic Operations"

　

5) Have the input condifions been met?

6) Replace bent hoss.

　

6) Is the air hose bent?

7) Replace the packing.

　

7) Is the packing inside the cylinder

　

　

   damaged?

1) 调整注塑机的限位开关并检查到控制盒的连线

　

　

2) 调整注塑机的限位开关并检查相关连线

　

1) 模开完成信号(MO)是否为ON

3) 逐渐松动阀门直到机械手开始下降

　

2) 机械手摆动复归和摆动到位的限位开

4) 更换损坏的阀门

　

    关是否工作正常?

5) 参看有关“手动操作“和“自动操作”

　

3) 机械手下降速度控制气阀是否锁得太

6）更换损坏的气管

　

   紧?

7) 更换密封

　

4) 电磁阀是否损坏？

　

　

5) 是否满足输入条件？

　

　

6) 气管是否被弯曲？

　

　

7) 气缸内部密封是否损坏？

　

No advance

1) Have the input conditions been met?

1) See the section "Manual Operations" and

movement

2) Is the advance speed control valve shut

   "Automatic Operations"

　

    too tightly?

2) Loosen gradually until advance movement

无前进动作

3) Is the solenoid valve bad?

   start

　

4) Is the air hose bent?

3) Replace bad valve

　

5) Is the packing inside the cylinder damaged?

4) Replace bent hose.

　

　

5) Replace the packing

　

1) 输入条件是否满足？

　

　

2) 前进的速度控制阀门是否关得太*？

1)  参看“手动操作”和“自动操作”

　

3) 电磁阀门是否损坏？

2) 逐渐松动阀门直到机械手开始前进

　

4) 气管是否被弯曲？

3) 更换损坏的阀门

　

5) 气缸内部密封是否损坏？ 

4) 更换气管

　

　

5) 更换密封

The Product is not

1) Are the input conditions met?

1) See the section "Manual Operations" and

gripped

2) The chuck cylinder is defective?

    "Automatic Operations"

　

3) The solenoid valve is defective?

2) Replace the chuck cylinder

产品未抓紧

4) Is the molding machine mold open stroke correct?

3) Replace the solenoid valve

　

5) Is the uploader crosswise stroke correct?

4) Adjust the molding open of molding machine.

　

6) Is the protrusion of ejector pin appropriate?Is the

5) Adjust the crosswise stroke.

　

   setting time on the timer appropriate?

6) Adjust the ejector advance stroke on the molding

　

7) The hose for the chuck pipe is loose.

    machine side

　

8)  Has mold separation deteriorated?

7) If the hose is loose, replace it with now one.

　

　

8) Apply mold separation solution or repair the metal

　

1) 输入条件是否满足？

    mold.

　

2) 产品夹的气筒是否损坏？

　

　

3) 电磁阀是否损坏？

1)  参看“手动操作”和“自动操作”

　

4) 注塑机的模开行程是否正确？

2) 更换夹子的气筒

　

5) 机械手的摆动行程是否正确？

3) 更换电磁阀

　

6) 顶针的顶出是否合适？定时器的时间设定是否合适?

4) 调整注塑机的开模

　

7) 夹子的气管是否松？

5)  调整摆动行程

　

8) 开模情况是否恶化

6)  调整注塑机的顶针顶出行程

　

7)  如果气管松，更换新的

　

8)  修理模具

No return

1) Have the input conditions been met?

1) See the section "Manual Operation"...

movement

2) Are the swing action-end and swing return-end limit

2) Adjust the limit switch on the molding machine 

　

    switches(on the extracting and release side)  

    and check the wiring.

无回位

    function correctlly?

3) Replace bad valve

　

3) Is the solenoid valve bad?

　

　

　

1)  参看“手动操作”和“自动操作”

　

1) 输入条件是否满足?

2) 调整注塑机的限位开关并检查相关连线

　

2) 机械手摆动复归和摆动到位的限位开关是否正常?

3) 更换坏的电磁阀

　

3) 电磁阀是否损坏?

　

No ascent

1) Have the input conditions been met?

1) See the section "Manual Operation"...

　

2) Is the ascent speed control valve shut too tightly?

2) Loosen gradually until ascent movement

无上升

3) Is the solenoid valve bad?

    starts

　

　

3) Replace bad valve